4.4.1.145 ValueSet http://hl7.org/fhir/ValueSet/devicealert-condition

1. An event has occurred (NOS)
2. Event (NOS).

1. Abnormal condition detected (NOS)
2. Abnormal condition detected.

1. Absent
2. Absent.

Active (NOS)

1. Alarm (NOS)
2. Alarm (NOS).

Connection

Contaminated

Defect is detected in a device, sensor, etc.

An agent is detected as depleted in a device, sensor, etc

Some signal or special condition was detected.

1. Disconnection, e.g., in sampling line
2. Disconnection, e.g., in sampling line.

1. Signal is disturbed.
2. {Airway gas concentration} signal is disturbed.

A reservoir, etc., is empty.

1. Unspecified device error
2. Unspecified device error.

1. Error condition is detected
2. Problem in power supply module.

Erratic condition is detected.

1. A reservoir, etc., has excess content
2. Excess(ive) [NOS].

1. A consumable is exhausted
2. Exhausted.

An action, data transmission, etc., failed.

{numeric observation} > high limit

A metric exceeds a given threshold

A metric exceeds a given threshold.

1. Incorrect result of a calculation, e.g., CRC in data transmission, of a data structure, etc., detected
2. Incorrect result of a calculation, e.g., CRC in data transmission, of a data structure, etc., detected.

1. Infiltration NOS
2. Infiltration [NOS].

1. Ingress of contaminant NOS
2. Ingress [NOS].

1. (Un)intentional inoperable condition NOS
2. (Un)intentional inoperable condition.

1. Interference NOS
2. Interference [NOS].

A measurement, process, or data transmission was interrupted.

Irregular rhythm or waveform in a signal, etc.

1. Leakage in a gas or fluid filled system detected
2. Leakage in a gas or fluid filled system detected.

{numeric observation} < low limit

A metric falls short of a given threshold

A metric falls short of a given threshold.

Signal or synchronization, etc., was lost.

1. Malfunction of a device, VMD, or sensor is detected.
2. {NMT} hardware malfunction; unplugging or restarting the {NMT} measurement module may correct the problem.

1. Mode status
2. Mode status (notification)

Signal is noisy.

1. Cuff not fully deflated
2. {NBP Cuff} Deflation error

Flow is hindered.

Overflow was detected in a measurement or calculation

Overflow was detected in a measurement or calculation.

1. Unspecified device error
2. Problem (NOS).

Flow is reversed

1. Error Event: Sensor electrical lead (e.g., ECG) is shorted (NOS)
2. Short (electrical) [NOS].

The display is stopped.

1. Subatmospheric [NOS]
2. Subatmospheric [NOS].

1. Unspecified device error sustained
2. Sustained [NOS].

1. Unanalyzable processing error message
2. Unanalyzable signal or measurement; cannot be processed.

Resource is unavailable.

Undefined.

Underflow was detected in a measurement or calculation

1. Unequal
2. Unequal.

VMD or signal is unknown.

1. A component (sensor, module) has become unplugged
2. A component (sensor, module or device) has become unplugged

1. Device has violated an operating parameter
2. Violation (NOS).

1. Indication: Device warming in Progress, No Measurement Possible
2. Warming [NOS].

1. Unspecified device error warning
2. Warning (NOS).

Weak signal was detected.

1. Recoverable state machine error in communication
2. Recoverable state machine error in communication.

1. Device has become inoperable
2. Unintentional inop.

1. Unrecoverable state machine error in communication
2. Unrecoverable state machine error in communication.

1. Error Event: Breath Absent (this is not apnea, but a technical ventilator event.)
2. Error Event: breath absent (this is not apnea, but a technical ventilator event.).

1. Calibration is not successful.
2. {SpO2} Only Mode (not fully calibrated)

1. Error Event: Communication Lost
2. {Monitor} No communications

1. Device configuration: combination is not valid.
2. {SpO2} Connection not supported

Unspecified problem in data acquisition

A resource is not available.

1. Signal gain high: probably erroneous data extraction
2. Gain high.

1. Signal gain low: probably erroneous data extraction
2. Gain low.

1. Not specified, unnormal handling of a device, device component, cabling, or transducer
2. Not specified, unnormal handling of a device, device component, cabling, or transducer.

1. Over inflated (non-specific)
2. Over-inflated.

1. Mix errror
2. Gas (or other) mixer inoperable.

1. Irregular position of a plug-in device
2. Problem in position of a plug-in device
3. Position irregular.
4. Irregular position of a plug-in device.

1. Irregular position of a plug-in device
2. Problem in position of a plug-in device
3. Position irregular.
4. Irregular position of a plug-in device.

1. Unspecified processing error
2. Unspecified processing error.

1. Signal amplitude is incorrect for processing
2. Signal out of range

1. Signal amplitude is too high for processing.
2. {Impedance respiration rate} Out of range (high)

1. Signal amplitude is too low for processing, e.g., waveform detection.
2. {ST} Out of range (low)

[Pattern] Shape error.

Error Event: Signal erratic

1. Error Event: Signal source absent
2. Source absent or missing.

1. Low voltage detected power supply
2. Unspecified tools or agents (e.g. calibration fluids) are low.

1. Problem in power supply
2. Supplies problem.

1. Unspecified quality of service event
2. Unspecified quality of service event.

1. Error in time synchronization
2. Error in time synchronization.

Synchronisation inoperable

1. Communication error: timeout
2. Timeout error.

Vibration hinders adequate measurement.

1. Pulmonary Capillary Wedge Pressure: occluded
2. Occluded [Wedged].

1. Battery failed or is defective
2. {*} Battery inoperable

1. Battery discharged or is defective.
2. {ecgResp} Battery low
3. {device or sensor} Battery low

Battery malfunction

Unspecified battery problem

1. Breathing system occlusion
2. Ventilator breathing system occlusion.

Use MDC_EVT_BUFF_OVERFLOW (3::502)

1. Communication error: cable short
2. {SpO2} Cable failure

1. Pulmonary Capillary Wedge Pressure: over inflation
2. {Pulmonary artery catheter} catheter cuff over-inflated.

A short circuit was detected in a VMD.

1. Exhausted CO2 absorber
2. Ventilator - exhausted CO2 absorber.

1. CO2 Canister leak
2. CO2 canister leak.

Defect occurred in a CO2 sample line

1. Carbon dioxide measurement window in a CO2 measuring device is occluded.
2. The airway CO2 sensor window is occluded.

1. Error Event: Communication Link Noisy
2. Comm link noisy.

1. Error Event: Communication Module Error
2. Communication module error.

1. Supply or disposable positioning problem
2. Supply or disposable positioning problem.

1. Connection short
2. Connector short.

1. Incorrect Cuff
2. Incorrect NIBP cuff type

Cuff leak

1. Cuff not fully deflated
2. {NBP} cuff not deflated.

1. Cuff over inflated
2. {NBP} cuff over-inflated, i.e. cuff pressure high.

A door or handle which must be closed for proper operation is open.

1. Electric power line: unspecified problem
2. Electric power line: unspecified problem.

1. Endotracheal tube leak (ventilator)
2. Endotracheal tube leak (ventilator).

1. Unspecified device malfunction error warning
2. {ECG} equipment malfunction.

1. Flow disturbance
2. Pump flow disturbance.

1. Infiltration of fluid line
2. Infiltration of fluid line.

1. Ingress in fluid line
2. Fluid line ingress.

1. Flow in tube is occluded
2. Tube occluded.

1. Problem in fluid line
2. Problem in fluid line.

1. Flow sensor problem
2. Flow sensor problem.

Gas contamination

1. Gas agent identification malfunction
2. Gas agent identification malfunction.

1. Gas line problem
2. Gas line problem (with the breathing system).

1. Heater power problem
2. Heating Power problem.

1. Leak in hose within breathing system
2. Leak in breathing system.

1. Flow in hose is obstructed
2. (Ventilator) hose obstructed.

1. Error Event: (ECG) Lead Disconnected (specialized form of the generic disconnect event. In case of ECG, some ECG devices reconstruct leads when a single lead of a multilead cable falls off. This needs a special user notification, because the situation might not be visible on the display waves. Reasoning: see above.)
2. Error Event: {ECG} Lead Disconnected (specialized form of the generic disconnect event). [In the case of ECG, some ECG devices reconstruct leads when a single lead of a multilead cable falls off. This needs a special user notification, because the situation might not be visible on the display waves. Reasoning: see above.]

1. Error Event: (ECG) Lead Noisy
2. {ECG} lead data is invalid due to excessive signal noise, bad electrode contact, interference from external devices and/or incorrect {ST} lead selection(s).

1. Error Event: (ECG) Lead Disconnected
2. {ECG} Lead off

1. Error Event: (ECG) Leads Disconnected
2. One or more {ECG} leads are not attached to the patient.

1. Lights in the (sleep measurement) room are switched off.
2. Lights in the {sleep measurement} room are switched off.

1. Error Event: Light Interference (SpO2 measurement, special kind of interference)
2. {SpO2} Regulation error: an excessive amount of ambient light is present, giving low amplitude and inaccurate readings as a result.

1. Error Event: Light source absent
2. Light source absent or missing.

1. Medical gas or supply low
2. Medical gas or supply low.

1. Module disconnnected
2. Module disconnected

1. Too many [plugin] modules
2. Too many modules.

1. [Plugin] Module unknown
2. [Plugin] Module unknown.

1. Subsystem disconnected
2. {Measurement module} subsystem disconnected.

1. Error Event: Communication Message Error
2. Subsystem has received false data packet.

1. Too low O2 delivery (concentration or flow)
2. Too low O2 delivery (concentration or flow).

1. Optical Module Absent
2. Optical module absent or missing.

1. Optical Module Defect
2. Optical module defect.

1. Problem with recording paper
2. [Hardcopy] paper problem.

1. Incorrect plugin [module]
2. Incorrect plugin [module].

Problem in position of a plug-in device

1. Sensor disconnection or fault
2. {SpO2} sensor disconnection or fault.

1. Sensor malfunction
2. {SpO2} sensor malfunction.
3. {SpO2} sensor malfunction, a current state or condition of faulty or improper functioning.

1. Flow sensor problem
2. {SpO2} sensor problem.

1. [CO2] Sidestream malfunction
2. {Airway CO2} sidestream malfunction.

1. [CO2] Sidestream off
2. {Airway CO2} sidestream off.

1. [CO2] Sidestream on
2. {Airway CO2} sidestream on.

1. Site timer problem
2. Site Timer Problem.

1. Communication error: unknown software version
2. Communication error: unknown software version.

1. Tube disconnected, e.g., disconnection in fresh gas flow hose
2. Tube disconnected, e.g. disconnection in fresh gas flow hose.

1. Leak in tube
2. Tube leak.

1. Flow in tube is obstructed
2. Tube obstructed.

Occlusion of fluid line.

1. Transducer absent
2. {Temperature} transducer absent or missing.

1. Error Event: Transducer Disconnected (specialized form of the generic disconnect event for measurements with intelligent transducer)
2. Error Event: {SpO2} transducer disconnected (specialized form of the generic disconnect event for measurements with intelligent transducer.

1. Transducer malfunctioning
2. {Predictive-temperature} transducer malfunctioning.

1. Bandwidth incorrect
2. Bandwidth incorrect.

1. Flow is low
2. {Pump} flow low.

1. Flow is reversed
2. {Ventilator} reverse flow (not specific to inspiratory or expiratory limb).

1. Error in drip counting measurement
2. Error in drip counting measurement.

1. Error Event: Radiation source intensity incorrect
2. Intensity error (NOS).

1. Error Event: Light source intensity incorrect
2. Light Intensity error.

1. Error Event: Measurement Unplugged (e.g., in modular patient monitor. Reasoning: In contrast to the disconnect events below, this event indicates that a measurement module was manually (==voluntarily) removed. Dependent on the alarm configuration of a monitor (specifically, with latched alarms), this condition must be announced to the user; and the user must specifically acknowledge the situation.)
2. Error Event: {*} measurement unplugged (e.g., in modular patient monitor. Reasoning: In contrast to the disconnect events below, this event indicates that a measurement module was manually (==voluntarily) removed. Dependent on the alarm configuration of a monitor (specifically, with latched alarms), this condition must be announced to the user; and the user must specifically acknowledge the situation.). [The optional attribute MDC_ATTR_EVT_INTENTIONALITY may be included in the alert message to indicate degree of intentionality by the user.]

1. Unspecified error in processing of a biosignal
2. Unspecified error in processing of {temperature} biosignal.

1. Error Event: Measurement Failed (e.g., a noninvasive blood pressure)
2. Error Event: {NBP} measurement failed (e.g., a noninvasive blood pressure).

1. Error Event: Measurement inoperable, Failed (e.g., a noninvasive blood pressure)
2. {SpO2} No measurement

1. Error Event: Measurement intereference (e.g., a noninvasive blood pressure)
2. Interference in measurement

Error Event: Measurement Interrupted (e.g., a noninvasive blood pressure) (there is a generic interrupted code for processing; however, this code does not have to do with processing. As an example of this code, the user might simply hit a stop button, and this action makes the measurement invalid.)

1. Error Event: Measurement Range Exceeded, i.e., the signal is out of the physiological range that is specified in the Metric object.
2. Error Event: Metric (measurement) overrange.
3. Error Event: {NBP} measurement range exceeded, i.e., the signal is out of the physiological range that is specified in the Metric object.

1. Error Event: Metric (measurement) underrange
2. {NBP} metric (measurement) underrange.

High pressure

High pressure

1. Pressure subatmospheric [Vent]
2. [Vent] Pressure subatmospheric.

1. High supply pressure
2. Supply pressure high.

1. Low supply pressure
2. Supply pressure low.

1. Cuff over pressure
2. {NBP} cuff overpressure.

1. Signal is low
2. {SpO2} signal low.

1. Error Event: Signal Cannot Be Analyzed (for any secondary derived measurement when the input signal is bad)
2. Error Event: Signal Cannot Be Analyzed (for any secondary derived measurement when the input signal is bad). [For example, {ECG QT} measurement is unanalyzable.]

1. Signal is overrange
2. Signal out of physical range.

1. Signal is underrange
2. Signal out of range.

1. Signal is weak
2. {SvO2} signal strength is weak.

1. Temperature exceeds limit
2. Temperature high: > limit.

1. Temperature value exceeds limit
2. Temperature high: value > limit.

1. Unit of measurement invalid
2. Unit of measurement invalid.

1. A component (sensor, module) is not supported
2. {CCO} unsupported.

A message contains wrong code.

1. Signal gain low: probably erroneous data extraction
2. Signal gain low: probably erroneous data extraction.

1. Unspecified handling error
2. Unspecified handling error.

Unspecified tools or agents (e.g., calibration fluids) are low.

1. Alarm limit exceeded
2. Alarm Limit.

1. Communication error: quality of service (QOS)
2. Unspecified Quality of Service event.

1. Unspecified timing error
2. Unspecified timing error.

1. Unspecified processing error message
2. Messaging Error.

Underflow was detected in a measurement or calculation.

1. Unspecified processing error
2. Unspecified processing event.

1. Ventilator - low O2 delivery
2. Ventilator - low O2 delivery (concentration or flow).

1. Synchronization event for synchronization of different processes
2. Synchronization event for synchronization of different processes.

1. Cuff improperly placed
2. {NBP} cuff has not been positioned correctly.

1. Artifact is detected in a waveform.
2. Artifact is detected in a {*} waveform.

Disturbed waveform: result may be erroneous.

1. Interference in measurement
2. Error due to interference in measurement

Shape/amplitude of waveform is abnormal.

Noisy signal: result may be erroneous.

Oscillation in waveform is expected, but not found.

1. Typically, a zero voltage signal
2. Typically, a zero voltage signal.

1. Signal is out of range.
2. {SvO2} signal is out of range.

1. Unspecified signal processing error
2. Unspecified signal processing error.

A metric exceeds a given threshold.

Subsystem has received false data packet.

1. Motions are detected, e.g., in NIBP measurement.
2. NBP motion artifact has been detected.

1. Cuff is disconnected or leaking, e.g., in NIBP.
2. NBP cuff is disconnected or leaking.

1. Problem in power supply
2. {*} power supply problem.

Signal voltage is out of range.

1. Failure occurred in a CO2 measuring device.
2. A failure occurred in the airway CO2 measuring device.

1. Fault occurred in carbon dioxide sensor disc.
2. A fault occurred in the airway CO2 sensor.

1. Sync puls: Start of ventilator inspiratory cycle
2. Sync puls: Start of ventilator inspiratory cycle.

1. Communication error: NOS
2. Unspecified communication event.

Subsystem has received false data packet.

1. Communication error: framing error
2. Communication error: framing error.

1. Communication error: parity error
2. Communication error: parity error.

1. A door or handle, which must be closed for operation, is open.
2. Door Open

1. Undefined communication message syntax
2. Undefined communication message syntax.

1. Timer tick of real-time clock for synchronization of all processes
2. Timer tick of real-time clock for synchronization of all processes.

1. Unspecified problem in data acquisition
2. Unspecified problem in data acquisition.

1. Error Event: Lights in the (sleep measurement) room are switched on {status lights on/off}
2. Lights in the {sleep measurement} room are switched on (or device status or illumination lights are on).

1. Abnormal low environmental temperature
2. Abnormal low environmental temperature.

1. Abnormal high environmental temperature
2. Abnormal high environmental temperature.

1. Too much humidity for accurate measurement
2. Too much humidity for accurate measurement.

1. Oscillation in signal is absent
2. No oscillation.

1. Signal amplitude is not as expected
2. Invalid signal - shape/amplitude of signal unnormal.

1. Pulserate coincidence
2. Pulserate coincidence.

1. Signal artifact detected
2. {ECG} Artifact

1. Communication timing error: buffer overflow
2. Communication timing error: buffer overflow.

Airway temperature is too high (ventilator).

1. Abnormal environmental temperature
2. Abnormal environmental temperature.

1. Example: obstruction of the endotracheal tube
2. Example: obstruction of the endotracheal tube.

Breathing volume is not constant.

The volume measurement in a ventilator is inoperable.

Respirator device temperature is too high.

The gas agent must be selected for it to be measured by the airway gas analyzer.

1. Ventilator synchronization inoperable
2. Ventilator synchronization inoperable.

1. Flow is disturbed
2. {Pump} flow impediment.

1. The expiratory valve is stuck.
2. Example: the expiratory valve is stuck.

1. A specified period for delivery has elapsed
2. Configured time to deliver whole syringe/bottle is over.

Device status report.

Gaseous agent mixing iris is inoperable in a ventilator (anesthesia).

1. A specified period for stnadby has elapsed
2. Standby Time Expired

Breathing system is vented.

1. Exhausted carbon dioxide absorber
2. Exhausted carbon dioxide absorber.

The airway CO2 gas sampling line is blocked.

1. Example: occlusion of the endotracheal tube
2. Example: occlusion of the endotracheal tube.

Ventilator device temperature is too high.

1. Disconnection of parts in a ventilator, e.g., disconnection in FGF hose
2. Disconnection of a part (or parts) in a ventilator, e.g., disconnection in FGF hose.

1. Inoperable inspiratory Omeasurement
2. The inspiratory O2 pressure sensor is inoperable.

1. Problem with gas lines to/from breathing system
2. Problem with gas lines to/from breathing system.

Gas mixer is inoperable.

1. Leak in breathing system
2. Leak in breathing system detected.

A metric falls short of a given threshold.

1. High pressure in fluid line
2. Too much pressure in line.

Problem in power supply

1. Unspecified device environment warning
2. Unspecified environment(al) event.

Patient is disconnected from ventilator.

1. Advisory: Syringe has taken longer than expec ted time
2. Syringe pre-alarm (x minutes).

User keyboard input is higher than available with syringe type (pump).

1. Ventilator is inoperable
2. The ventilator is inoperable.

1. An unspecified component of the ventilator is stuck in position [if the expiratory valve is specifically known to be stuck, use MDC_EVT_VENT_EXP_VALVE_STUCK (3::522)]
2. {Expiratory valve} is stuck.

Configured time to deliver whole syringe/bottle is over.

1. Flow is obstructed.
2. {Pump} flow is hindered.

1. Too much humidity for accurate measurement
2. Too much humidity for accurate measurement.

1. High pressure in fluid line
2. Too much pressure in line.

1. Advisory: Flow resistance warning
2. Flow resistance warning.

Timeout: device should be either operated or turned off.

1. Total volume infused (pump)
2. Total programmed volume infused (pump).
3. Infusion complete, where the programmed volume has been infused (pump).

1. Disposables low or out
2. Disposables low or out.

1. Unspecified equipment event
2. Unspecified Equipment event.

Air in fluid line.

1. Too low O2 delivery (flow)
2. Too low oxygen delivery (flow).

1. Too low O2 delivery (concentration)
2. Too low oxygen delivery (concentration).

1. Pump in free flow
2. Pump in free flow.

1. Incompatibility of nomenclature or processing component, etc.
2. This version of the {NMT} measurement module is not supported, or the module firmware is incomplete and needs to be upgraded.

The multiple reply remote operation function is not available (see Clause 6 in ISO/IEEE 11073-20101:2004)

1. Event, non-specific [NOS] (This code is unusual as it applies only to an object.)
2. Event, non-specific [NOS]

1. No breathing within a pre-configured time span
2. Apnea

1. Beat not paced
2. No pacer detected

No QRS-complex found in predefined time period

Missed beat within some regular ECG rhythm

1. Unusual beat within some regular ECG rhythm
2. Unusual beat

1. Ventricular bigemini: a specific rhythm
2. Ventricular bigeminy
3. Ventricular bigeminy: a specific rhythm

1. Bradycardia
2. Sinus bradycardia

Limit Event: Extreme Bradycardia (escalated low HR limit, not a brady rhythm)

1. Sustained Bradycardia
2. Sustained bradycardia.

1. Fibrillation (non-specific)
2. Fibrillation

1. No Ectopic beat
2. No ectopic beat

Pacer pulse sensed by heart

Pacer operational and controlling heart rhythm

1. Pacing captured (recognized by heart)
2. Pacing capture

1. Pacer not captured (not recognized by heart)
2. Pacing not captured (not recognized by heart)

1. Run of paced beats
2. Pacing Run

Unspecified ECG (arrhythmia) event

1. Prolonged RR interval, due to any reason
2. Pause

Quadrigeminy

Rhythm

No [cardiac] rhythm

Ectopic rhythm

Irregular rhythm

Tachycardia

Limit Event: Extreme Tachycardia (escalated high HR limit, not a tachy rhythm)

1. Tacycardia (unspecified)
2. Tachycardia Unspecified

1. Ventricular trigeminy
2. Trigeminy

Atrial fibrillation

Premature atrial contraction

1. Atrial Pacing
2. Atrial Pacing.

1. Atrial standstill
2. Atrial Standstill.

Atrial tachycardia

1. Atrial tachycardia multifocal
2. Atrial Tachycardia Multifocal

1. Atrial tachycardia paroxysmal
2. Atrial Tachycardia Paroxysmal

1. AV Disassociation
2. AV Dissociation

AV Pacing Sequential

1. AV block 1°.
2. AV block 1°

1. AV block 2°.
2. AV block 2°

1. AV block 2, Type I
2. AV Heart Block Degree 2 Type I

1. AV block 2, Type II
2. AV Heart Block Degree 2 Type II

1. Bundle Branch block
2. Bundle Branch Block

1. High heart rate
2. High Heart Rate

Error Event: Irregular heart rate (which means the beat detector finds a highly variable heart rate and cannot derive a consistent/stable value)

1. Low heart rate
2. Low Heart Rate

1. Heartbeat
2. [Heart] Beat

1. Dying heart
2. Dying Heart

1. Heart block
2. Heart Block

1. Complete Heart block
2. Heart Block Complete

1. Junctional premature contraction
2. Premature Contraction, Junctional

Junctional tachycardia

1. Paroxysmal Junctional tachycardia
2. Paroxysmal supraventricular tachycardia

1. Left Anterior Fascicular Block
2. Fascicular Block. LA.

1. Left Bundle Branch block
2. Left Bundle Branch Block

1. Left Posterior Fascicular Block
2. Fascicular Block. LP

Pacer (device) not sensing

1. Patient not paced
2. Patient Not Paced

1. Right Bundle Branch block
2. Right Bundle Branch Block

1. Supraventricular beat
2. SV Beat

Supraventricular extrasystole

Supraventricular tachycardia

Ventricular parasystole

1. Ventricular bigeminy
2. Ventriclular bigeminy

Ventricular fibrillation

Ventricular flutter

Premature ventricular contraction

Premature ventricular contraction, R-on-T

Multiformed premature ventricular contractions

Pair of premature ventricular contractions

Several consecutive ventricular extrasystoles

VPC Triplet

1. Ventricular Pacing
2. Ventricular pacing

1. Ventricular quadrigeminy
2. Ventricular Quadrigeminy

Ventricular rhythm: escalation of Run of PVC, not yet flutter

1. Ventricular standstill
2. Ventricular Standstill

Ventricular tachycardia

1. Ventricular tachycardia, Non-sustained
2. Ventricular Tachycardia, Non-sustained

1. Ventricular tachycardia, Sustained
2. Ventricular Tachycardia, Sustained

1. Ventricular tachycardia, Torsades de Pointes
2. Torsades de Pointes

1. Ventricular tachycardia Rhythm
2. Ventricular Tachycardia Rhythm

1. Ventricular tachycardia Rhythm, Sustained
2. Vent Tachycardia Rhythm, Sustained

1. Ventricular trigemini: a specific rhythm
2. Ventricular trigeminy
3. Ventricular trigeminy: a specific rhythm

1. Ventricular trigeminy rhythm
2. Ventricular Trigeminy Rhythm

1. Current ectopic rhythm status: conveys an enumerated summary of the predominant ECG ectopic rhythm type(s) over the reporting time interval
2. Present ectopic arrhythmia type; "present" implies user-defined time-constant (e.g. within last minute).

1. Current rhythm status: conveys an enumerated summary of the predominant ECG rhythm type(s) over the reporting time interval
2. Present rhythm; "present" implies user-defined time-constant (e.g. within last minute)

Cardiac and Pulse Rates are unequal

1. Limit Event: Desaturation (escalated low oxygen alarm, used esp. in neonatal)
2. SpO2 Desaturation

Several consecutive supraventricular extrasystoles

A specific limit alert on the PVC rate

Spikes and waves in EEG

Breathing volume not constant

1. AV block 3°.
2. AV block 3°

Junctional rhythm

Sinus tachycardia

Clinical seizure discharge in EEG

Unspecified ECG (arrhythmia) event

Epileptiform discharges in EEG

Sharp spikes in EEG

Couplet

Frequent premature ventricular contractions

Atrial flutter

1. Assisted spontaneous breathing longer than a predefined time span (PSW)
2. Assisted spontaneous breathing longer then a predefined time span (PSW)

2:1 AV block

3:1 AV block

Apnea - pressure absent for 15 seconds

No pacer detected

4:1 AV block

Frequent supraventricular extrasystoles

Apnea - no volume exhale for 30 seconds

Pacer artifact recognized

1. Heart rate and respiration rate are reported to be the same value.
2. Cardiac and Respiration Rates are reported to be equal.

1. Junctional escape beats
2. Junctional Escape Beats.

Run of junctional tachycardia

Cardiac and Pulse Rates are equal

Back Activity Absent

Back Activity Asymmetric

1. NIBP non pulsatile
2. Pulse absent or non-pulsatile

1. Indication: Alarm Intentionally Off (disabled)
2. Indication: Alarm Intentionally Off (disabled). [This term is deprecated; use MDC_EVT_STAT_AIS_ALARM_OFF instead.]

1. Indication: Alarm Intentionally On (enabled)
2. Indication: Alarm Intentionally On (enabled). [This term is deprecated; use MDC_EVT_STAT_AIS_ENABLED instead.]

1. Indication: Device in Backup mode, No Measurement Possible
2. Status: Backup mode.

Battery is now being recharged.

1. Indication: Device in Calibration mode, No Measurement Possible
2. Calibration Mode or status [NOS].

1. Indication: Calibration in Progress, No Measurement Possible
2. {SpO2} Sensor calibrating

1. Indication: Calibration of invivo probe in Progress, No Measurement Possible
2. Status: Invivo Calibration running.

1. Indication: Calibration of light source in Progress, No Measurement Possible
2. Status: Light Calibration running.

1. Indication: Calibration of an optical (or other) sensor prior to insertion of a sensor/catheter
2. Status: Pre-insertion Calibration running.

1. Indication: Configuration in Progress, No Measurement Possible
2. Status: Configuring {*}.

1. Indication: Self test in Progress, No Measurement Possible
2. Status: {Cardiac output} self test running.

1. Indication: In standby mode, No Measurement Possible
2. Indication: standby.

Indication: Diagnostic test in Progress, No Measurement Possible

1. Indication: Zero calibration in Progress, No Measurement Possible
2. Status: Zero running.

1. Indication: Optical sensor connected
2. Status: {SvO2} optical module connected.

1. Indication: Optical sensor warming in Progress, No Measurement Possible
2. Status: {SvO2} optical module sensor or component warming up.

1. Indication: Sensor warming in Progress, No Measurement Possible
2. Status: {Airway gas analyzer} sensor warming.

1. Indication: Device warming in Progress, No Measurement Possible
2. Status: {*} sensor or component warming.

1. [Vent] Pressure sustained
2. Status: [Vent] Pressure sustained.

Status: All ECG alarms are off (still need these in France to meet French homologation, despite MDD).

Status: Some ECG alarms are off (still need these in France to meet French homologation, despite MDD).

Sigh mode is active.

VMD is not calibrated.

The function of gaseous agent mixing iris in a ventilator (anesthesia machine) is disabled.

1. Active state of, e.g., device
2. Active state of, e.g., device.

1. Respiratory volume time is limited.
2. Tidal volume is time limited.

1. Respiratory volume pressure is limited.
2. Tidal volume is pressure limited.

1. Tachyapnea alarm in a ventilator is disabled.
2. Tachyapnea alarm in a ventilator is disabled. [This term is deprecated; use MDC_EVT_STAT_VENT_TACHYPNEA_AIS_ALARM_OFF instead.]

1. Charging state of, e.g., battery
2. Charging state of, e.g., battery.

1. Alarm is silenced (speaker off).
2. Alarm is silenced (speaker off). [This term is deprecated; use MDC_EVT_STAT_AIS_AUDIO_OFF instead.]

1. Alarm state of, e.g., device or signal
2. Alarm state of, e.g., device or signal.

1. Door in the (sleep measurement) room is opened.
2. Door in the {sleep measurement} room is opened.

1. NIBP is inflating cuff to maximum cuff pressure.
2. Noninvasive blood pressure device is inflating cuff to maximum cuff pressure.

1. Indication: Learning - analyzing waveform
2. The {ECG} signal processing algorithm is in the «learning» state.

1. Device or VMD is in off condition.
2. Off (e.g. device or VMD is in an off condition)

1. Indication: Device In Standby Mode
2. Indication: the {*} device or subsystem is In standby mode.

1. Tachyapnea alarm is disabled.
2. Tachyapnea alarm is disabled. [This term is deprecated; use MDC_EVT_STAT_TACHYPNEA_AIS_ALARM_OFF instead.]

Device or VMD is in test mode.

1. Device or VMD learns waveform for recognition.
2. {ecgResp} Learning
3. {ecg or other algorithm} Learning

1. Door in the (sleep measurement) room is closed.
2. Door in the {sleep measurement} room is closed.

A sensor, absorber, etc., is depleted.

1. NIBP is deflating cuff and measuring blood pressure.
2. Noninvasive blood pressure device is deflating cuff and measuring blood pressure.

1. Connected state of device, sensor, etc.
2. Connected state of {*} device, sensor, etc.

Disconnection of a sensor, device, etc.

1. Sound in the (sleep measurement) room is switched off.
2. Sound in the {sleep measurement} room is switched off.

1. Lights in the (sleep measurement) room are switched on.
2. Lights in the {sleep measurement} room are switched on.

1. Sound in the (sleep measurement) room is switched on.
2. Sound in the {sleep measurement} room is switched on.

1. Device or VMD is in on condition
2. On (e.g. device or VMD is in an on condition)

1. Carbon dioxide monitor in warm-up mode
2. The airway CO2 monitor in warm-up mode.

1. Carbon dioxide alarm is disabled.
2. Carbon dioxide alarm is disabled. [This term is deprecated; use MDC_EVT_STAT_CO2_AIS_ALARM_OFF instead.]

1. The beep is off (QRS).
2. QRS detection auditory information signal is off.

1. Apnea alarm is disabled.
2. Apnea alarm is disabled. [This term is deprecated; use MDC_EVT_STAT_APNEA_RELATED_AIS_ALARM_OFF instead.]

Device is battery operated.

1. Report of functional status of device
2. Device (functional) status.

Device is in pediatric mode.

Device is in adult mode.

Device is mains-operated.

Device, e.g., pump, is in computer-controlled mode.

1. Device changed to mains-operated
2. Indication: power supply by line, likely by operator selection.

1. Device changed to battery operation
2. Indication: power supply by battery, likely by operator selection.

1. Carbon dioxide is not calibrated.
2. The airway CO2 monitor is not calibrated.

1. Indication: Device Active/Pump Running
2. {NBP} Running

1. Spontaneous breath of the patient, e.g., during weaning
2. Spontaneous breath of the patient, e.g., during weaning.

1. Machine generated breath of the patient, e.g., during weaning
2. Machine generated breath of the patient, e.g., during weaning.

1. Advisory: Check device or system (NOS)
2. Check {fresh-gas setting}

Advisory: Check Calibration

1. Advisory: Calibration required
2. Advisory: {NBP} calibration required.

1. Advisory: Check Calibration/Zero (system is not sure if calibration data is still ok.)
2. Advisory: Check Calibration/Zero required
3. Advisory: Check {invasive blood pressure} calibration/zero (device or system is not sure if calibration data is still ok.).

1. Advisory: Check Configuration
2. Advisory: Check configuration.

1. Advisory: Check Settings
2. Advisory: Check setting[s].

1. Advisory: Check Set up
2. Advisory: Check setup.

1. Advisory: Check Source
2. Advisory: Check data source or module.

1. Advisory: Check Zero
2. Advisory: Check zero, e.g. check {invasive blood pressure} zero.

1. Advisory: Condition Battery (battery needs a special ‘condition’ charge cycle for full capacity.)
2. Advisory: Condition Battery (battery needs a special 'condition' charge cycle for full capacity.).

1. Advisory: Replace Battery (a full charge is now a too small fraction of the original capacity or this is not a rechargeable battery that is close to empty.)
2. Advisory: Replace Battery (a full charge is now a too small fraction of the original capacity, or this is not a rechargeable battery that is close to empty.).

1. Advisory: Check cable
2. Advisory: Check cable.

1. Advisory: Check CO sensor
2. Advisory: Check the airway CO2 sensor.

1. Advisory: Check communication cable
2. Advisory: Check comm cable.

1. Advisory: Replace disposable
2. Advisory: Replace disposable.

1. Advisory: Check gas agent
2. Advisory: Check gas agent.

1. Advisory: Check patient lead or connector
2. Advisory: Check patient {ECG} leads or connector.

1. Advisory: Check O sensor
2. Advisory: Check O2 sensor.

1. Problem with recording paper subdevice
2. Problem with recording paper subdevice.

1. The sensor must be checked.
2. Advisory: Check sensor.
3. {ecgResp} Check sensor
4. {sensor} Check sensor

1. Advisory: Check Log (a fatal system error was entered in a log object and should be read.)
2. Advisory: Check Log (a fatal system error was entered in a log object and should be read.).

1. Advisory: Check volume sensor
2. Advisory: Check volume sensor.

1. Advisory: Decrease Gain (system asks user to decrease the gain; this advisory is different from the overrange error, ErrorEvent, that already is in the nomenclature; it is an "advisory.")
2. Advisory: Signal voltage out of range; gain adjustment necessary
3. Advisory: Decrease Gain (system asks user to decrease the gain; this advisory is different from the overrange error, ErrorEvent, that already is in the nomenclature; it is an "advisory.").

1. Advisory: Signal voltage out of range; gain adjustment necessary
2. Signal voltage out of range.

1. Advisory: Check time (system asks user to check the time)
2. Advisory: Check time.

1. Advisory: Check unit (system asks user to check unit)
2. Advisory: Check units [of msmt].

1. Advisory: Syringe needs to be replaced soon.
2. Syringe needs to be replaced soon.

Syringe needs to be replaced immediately.

1. Checking of water trap in a ventilator is necessary.
2. Advisory: Check water trap in a ventilator.
3. Check ventilator water trap.

Advisory: Vaporizer is not connected, not known or not allowed.

1. Checking of airway pressure in a ventilator is necessary.
2. Advisory: Check airway pressure in ventilator.

1. Checking of flow sensor in a ventilator is necessary.
2. Check flow sensor in a ventilator.

Flow calibration of ventilator is necessary.

1. The mixing iris in agent vaporizer in a ventilator must be checked (anesthesia machine).
2. The mixing iris in agent vaporizer in an ventilator must be checked (anesthesia machine).

Checking of ventilator air supply is necessary.

1. Checking of expiration valve is necessary.
2. Check expiration valve.
3. Checking of expiratory valve is necessary.

Warning that device will go to standy

1. Maintenance is required
2. Maintenance is required (This code is unusual as it applies only to an object.)
3. A device has identified the need for maintenance (e.g., PM period has expired)

IV Fluid pressure is too high on the downstream patient side.

Plunger out of position

Flange out of position

Syringe barrel capture fault.

Pressure disc out of position

End of plunger travel

Syringe is empty

1. Advisory: Patient controlled analgesia: door unlocked
2. PCA Door is unlocked

1. Advisory: Patient controlled analgesia: handset detached
2. PCA Handset is detached from unit.

1. Advisory: Patient controlled analgesia: maximum limit reached
2. Maximum PCA dose limit reached

1. Advisory: Patient controlled analgesia: paused
2. PCA paused, reason not specified.

Delivery Start

Delivery Stop (or Paused)

Delivery Complete

1. Communication status change
2. Communication Status Change

Program Cleared

Auto-Program Cleared

1. Advisory: The patient connected to a device has changed
2. Patient Change

1. Advisory: The ID of the patient connected to the device has changed
2. Patient ID Change

1. Advisory: The patient weight has changed
2. Patient Weight Change

1. Idle state of, e.g., device
2. Idle state of, e.g., {pump} device

1. Callback
2. Callback notififaction to the clinician, e.g. that the secondary infusion has been completed

1. Advisory: Infusion of the specified volume has been completed
2. Infusion complete, where the volume is deternined by the size of the container.
3. Infusion complete, where the volume is determined by the size of the container.

1. Advisory: Infusion of the specified volume is nearly complete
2. Infusion near completion, where the volume us determined by the size of the container.
3. Infusion near completion, where the volume is determined by the size of the container.

1. Battery depleted
2. Depleted Battery

1. Battery service required
2. Service Battery

Emergency Stop

1. Loss of power supply
2. Power Loss

Flow stop valve is open

1. Advisory: Check Intravenous Set
2. Check IV set.

An unknown event has occurred.

Programmed start delay will not be reached

Pump chamber blocked.

1. Advisory: Handset detached
2. {*} Handset is detached from unit

Pump volume counters cleared

Device time, civil time zone offsett and/or cumulative leap second information has changed

1. Any patient parameter has changed, e.g., body mass, height, and/or BSA.
2. Any patient parameter has changed, e..g. body mass, height and/or BSA.

1. Occlusion of upstream fluid line, from pump to IV fluid sources (aka proximal).
2. Occlusion of upstream fluid line, from pump to IV fluid sources (aka proximal)

1. Occlusion of downstream fluid line, from pump to patient (aka distal)..
2. Occlusion of downstream fluid line, from pump to patient (aka distal)

1. Air in upstream fluid line, from pump to IV fluid sources (aka proximal).
2. Air in upstream fluid line, from pump to IV fluid sources (aka proximal)

1. Air in downstream fluid line, from pump to patient (aka distal).
2. Air in downstream fluid line, from pump to patient (aka distal)

Invalid data (for any reason, including missing data)

Missing data (e.g., telemetry data dropouts)

1. Report of location of a device as item
2. Report of location of a device as item.

1. Report of location of a person as item
2. Report of location of a person as item.

1. Report of movement of expected stationary item
2. Report of movement of expected stationary item.

1. Report of constrained location item exceeding defined boundary
2. Report of constrained location item exceeding defined boundary.

1. Report of item colocation with another item
2. Report of item colocation with another item.

1. Report of expected moving item dwelling in location longer than a defined period
2. Report of expected moving item dwelling in location longer than a defined period.

1. Report of item acceleration increase potentially due to leaning or falling
2. Report of item aceleration increase potentially due to leaning or falling.

1. Report of item tamper interlock being indicated
2. Report of item tamper interlock being indicated.

1. Report of operator interaction with item by button press, cord pull
2. Report of operator interaction with item by button press, cord pull.

1. Report of loss of communication with item
2. Report of loss of communication with item.

1. Report of item environment of temperature, humidity, pressure, gases
2. Report of item environment of temperature, humidity, pressure, gases.

1. Report of item active tag battery status
2. Report of item active tag battery status.

Cuff loose

1. Indication: Alarm paused
2. Alarm is paused (visual and audio indications are off). [This term is deprecated; use MDC_EVT_STAT_AIS_ALARM_PAUSED instead.]

An event or report regarding software version and update status

An event or report regarding that the TLS (Transport Layer Security) certificate is about to expire or has expired

Definition for base term 3::0 MDC_EVT is: 1. An event has occurred (NOS) 2. Event (NOS).

Definition for base term 3::2 MDC_EVT_ABNORM is: 1. Abnormal condition detected (NOS) 2. Abnormal condition detected.

Definition for base term 3::4 MDC_EVT_ABSENT is: 1. Absent 2. Absent.

Definition for base term 3::6 MDC_EVT_ACTIVE is: Active (NOS)

Definition for base term 3::6676 MDC_EVT_ADVIS_BATT_COND is: 1. Advisory: Condition Battery (battery needs a special ‘condition’ charge cycle for full capacity.) 2. Advisory: Condition Battery (battery needs a special 'condition' charge cycle for full capacity.).

Definition for base term 3::6678 MDC_EVT_ADVIS_BATT_REPLACE is: 1. Advisory: Replace Battery (a full charge is now a too small fraction of the original capacity or this is not a rechargeable battery that is close to empty.) 2. Advisory: Replace Battery (a full charge is now a too small fraction of the original capacity, or this is not a rechargeable battery that is close to empty.).

Definition for base term 3::6680 MDC_EVT_ADVIS_CABLE_CHK is: 1. Advisory: Check cable 2. Advisory: Check cable.

Definition for base term 3::6664 MDC_EVT_ADVIS_CALIB_AND_ZERO_CHK is: 1. Advisory: Check Calibration/Zero (system is not sure if calibration data is still ok.) 2. Advisory: Check Calibration/Zero required 3. Advisory: Check {invasive blood pressure} calibration/zero (device or system is not sure if calibration data is still ok.).

Definition for base term 3::6660 MDC_EVT_ADVIS_CALIB_CHK is: Advisory: Check Calibration

Definition for base term 3::6662 MDC_EVT_ADVIS_CALIB_REQD is: 1. Advisory: Calibration required 2. Advisory: {NBP} calibration required.

Definition for base term 3::6658 MDC_EVT_ADVIS_CHK is: 1. Advisory: Check device or system (NOS) 2. Check {fresh-gas setting}

Definition for base term 3::6682 MDC_EVT_ADVIS_CO2_SENSOR_CHK is: 1. Advisory: Check CO sensor 2. Advisory: Check the airway CO2 sensor.

Definition for base term 3::6684 MDC_EVT_ADVIS_COMM_CABLE_CHK is: 1. Advisory: Check communication cable 2. Advisory: Check comm cable.

Definition for base term 3::6666 MDC_EVT_ADVIS_CONFIG_CHK is: 1. Advisory: Check Configuration 2. Advisory: Check configuration.

Definition for base term 3::6686 MDC_EVT_ADVIS_DISPOS_REPLACE is: 1. Advisory: Replace disposable 2. Advisory: Replace disposable.

Definition for base term 3::6704 MDC_EVT_ADVIS_GAIN_DECR is: 1. Advisory: Decrease Gain (system asks user to decrease the gain; this advisory is different from the overrange error, ErrorEvent, that already is in the nomenclature; it is an "advisory.") 2. Advisory: Signal voltage out of range; gain adjustment necessary 3. Advisory: Decrease Gain (system asks user to decrease the gain; this advisory is different from the overrange error, ErrorEvent, that already is in the nomenclature; it is an "advisory.").

Definition for base term 3::6706 MDC_EVT_ADVIS_GAIN_INCR is: 1. Advisory: Signal voltage out of range; gain adjustment necessary 2. Signal voltage out of range.

Definition for base term 3::6688 MDC_EVT_ADVIS_GAS_AGENT_CHK is: 1. Advisory: Check gas agent 2. Advisory: Check gas agent.

Definition for base term 3::6690 MDC_EVT_ADVIS_LEAD_CHK is: 1. Advisory: Check patient lead or connector 2. Advisory: Check patient {ECG} leads or connector.

Definition for base term 3::6692 MDC_EVT_ADVIS_O2_SENSOR_CHK is: 1. Advisory: Check O sensor 2. Advisory: Check O2 sensor.

Definition for base term 3::6714 MDC_EVT_ADVIS_PUMP_SYRINGE_REPLACE_IMMED is: Syringe needs to be replaced immediately.

Definition for base term 3::6712 MDC_EVT_ADVIS_PUMP_SYRINGE_REPLACE_WARN is: 1. Advisory: Syringe needs to be replaced soon. 2. Syringe needs to be replaced soon.

Definition for base term 3::6694 MDC_EVT_ADVIS_REC_PAPER_REPLACE is: 1. Problem with recording paper subdevice 2. Problem with recording paper subdevice.

Definition for base term 3::6696 MDC_EVT_ADVIS_SENSOR_CHK is: 1. The sensor must be checked. 2. Advisory: Check sensor. 3. {ecgResp} Check sensor 4. {sensor} Check sensor

Definition for base term 3::6668 MDC_EVT_ADVIS_SETTINGS_CHK is: 1. Advisory: Check Settings 2. Advisory: Check setting[s].

Definition for base term 3::6670 MDC_EVT_ADVIS_SETUP_CHK is: 1. Advisory: Check Set up 2. Advisory: Check setup.

Definition for base term 3::6672 MDC_EVT_ADVIS_SRC_CHK is: 1. Advisory: Check Source 2. Advisory: Check data source or module.

Definition for base term 3::6698 MDC_EVT_ADVIS_STATUS_LOG_CHK is: 1. Advisory: Check Log (a fatal system error was entered in a log object and should be read.) 2. Advisory: Check Log (a fatal system error was entered in a log object and should be read.).

Definition for base term 3::6708 MDC_EVT_ADVIS_TIME_CHK is: 1. Advisory: Check time (system asks user to check the time) 2. Advisory: Check time.

Definition for base term 3::6710 MDC_EVT_ADVIS_UNIT_CHK is: 1. Advisory: Check unit (system asks user to check unit) 2. Advisory: Check units [of msmt].

Definition for base term 3::6718 MDC_EVT_ADVIS_VAPORISER_CHK_DISCONN is: Advisory: Vaporizer is not connected, not known or not allowed.

Definition for base term 3::6728 MDC_EVT_ADVIS_VENT_AIR_SUPP_CHK is: Checking of ventilator air supply is necessary.

Definition for base term 3::6730 MDC_EVT_ADVIS_VENT_EXP_VALVE_CHK is: 1. Checking of expiration valve is necessary. 2. Check expiration valve. 3. Checking of expiratory valve is necessary.

Definition for base term 3::6724 MDC_EVT_ADVIS_VENT_FLOW_CALIB is: Flow calibration of ventilator is necessary.

Definition for base term 3::6722 MDC_EVT_ADVIS_VENT_FLOW_SENSOR_CHK is: 1. Checking of flow sensor in a ventilator is necessary. 2. Check flow sensor in a ventilator.

Definition for base term 3::6726 MDC_EVT_ADVIS_VENT_MIX_IRIS_CALIB is: 1. The mixing iris in agent vaporizer in a ventilator must be checked (anesthesia machine). 2. The mixing iris in agent vaporizer in an ventilator must be checked (anesthesia machine).

Definition for base term 3::6720 MDC_EVT_ADVIS_VENT_PRESS_AWAY_CHK is: 1. Checking of airway pressure in a ventilator is necessary. 2. Advisory: Check airway pressure in ventilator.

Definition for base term 3::6716 MDC_EVT_ADVIS_VENT_WATER_TRAP_CHK is: 1. Checking of water trap in a ventilator is necessary. 2. Advisory: Check water trap in a ventilator. 3. Check ventilator water trap.

Definition for base term 3::6702 MDC_EVT_ADVIS_VOL_SENSOR_CHK is: 1. Advisory: Check volume sensor 2. Advisory: Check volume sensor.

Definition for base term 3::6674 MDC_EVT_ADVIS_ZERO_CHK is: 1. Advisory: Check Zero 2. Advisory: Check zero, e.g. check {invasive blood pressure} zero.

Definition for base term 3::410 MDC_EVT_AL_LIMIT is: 1. Alarm limit exceeded 2. Alarm Limit.

Definition for base term 3::8 MDC_EVT_ALARM is: 1. Alarm (NOS) 2. Alarm (NOS).

Definition for base term 3::3072 MDC_EVT_APNEA is: 1. No breathing within a pre-configured time span 2. Apnea

Definition for base term 3::3306 MDC_EVT_BACK_ACTIV_ASYM is: Back Activity Asymmetric

Definition for base term 3::728 MDC_EVT_BATT_DEPL is: 1. Battery depleted 2. Depleted Battery

Definition for base term 3::192 MDC_EVT_BATT_FAIL is: 1. Battery failed or is defective 2. {*} Battery inoperable

Definition for base term 3::194 MDC_EVT_BATT_LO is: 1. Battery discharged or is defective. 2. {ecgResp} Battery low 3. {device or sensor} Battery low

Definition for base term 3::196 MDC_EVT_BATT_MALF is: Battery malfunction

Definition for base term 3::198 MDC_EVT_BATT_PROB is: Unspecified battery problem

Definition for base term 3::730 MDC_EVT_BATT_SERV is: 1. Battery service required 2. Service Battery

Definition for base term 3::136 MDC_EVT_BREATH_ABSENT is: 1. Error Event: Breath Absent (this is not apnea, but a technical ventilator event.) 2. Error Event: breath absent (this is not apnea, but a technical ventilator event.).

Definition for base term 3::502 MDC_EVT_BUFF_OVERFLOW is: 1. Communication timing error: buffer overflow 2. Communication timing error: buffer overflow.

Definition for base term 3::340 MDC_EVT_BW_INCORRECT is: 1. Bandwidth incorrect 2. Bandwidth incorrect.

Definition for base term 3::204 MDC_EVT_CABLE_SHORT is: 1. Communication error: cable short 2. {SpO2} Cable failure

Definition for base term 3::138 MDC_EVT_CALIB_FAIL is: 1. Calibration is not successful. 2. {SpO2} Only Mode (not fully calibrated)

Definition for base term 3::722 MDC_EVT_CALLBACK is: 1. Callback 2. Callback notififaction to the clinician, e.g. that the secondary infusion has been completed

Definition for base term 3::206 MDC_EVT_CATH_PULM_INFLAT_OVER is: 1. Pulmonary Capillary Wedge Pressure: over inflation 2. {Pulmonary artery catheter} catheter cuff over-inflated.

Definition for base term 3::738 MDC_EVT_CHECK_IV_SET is: 1. Advisory: Check Intravenous Set 2. Check IV set.

Definition for base term 3::208 MDC_EVT_CKT_SHORT is: A short circuit was detected in a VMD.

Definition for base term 3::212 MDC_EVT_CO2_CAN_LEAK is: 1. CO2 Canister leak 2. CO2 canister leak.

Definition for base term 3::462 MDC_EVT_CO2_MSMT_FAIL is: 1. Failure occurred in a CO2 measuring device. 2. A failure occurred in the airway CO2 measuring device.

Definition for base term 3::214 MDC_EVT_CO2_SAMPL_LINE_DEFECT is: Defect occurred in a CO2 sample line

Definition for base term 3::464 MDC_EVT_CO2_SENSOR_FAIL is: 1. Fault occurred in carbon dioxide sensor disc. 2. A fault occurred in the airway CO2 sensor.

Definition for base term 3::216 MDC_EVT_CO2_WIND_OBSTRUC is: 1. Carbon dioxide measurement window in a CO2 measuring device is occluded. 2. The airway CO2 sensor window is occluded.

Definition for base term 3::468 MDC_EVT_COMM is: 1. Communication error: NOS 2. Unspecified communication event.

Definition for base term 3::218 MDC_EVT_COMM_LINK_NOISY is: 1. Error Event: Communication Link Noisy 2. Comm link noisy.

Definition for base term 3::140 MDC_EVT_COMM_LOST is: 1. Error Event: Communication Lost 2. {Monitor} No communications

Definition for base term 3::220 MDC_EVT_COMM_MODULE_ERR is: 1. Error Event: Communication Module Error 2. Communication module error.

Definition for base term 3::686 MDC_EVT_COMM_STATUS_CHANGE is: 1. Communication status change 2. Communication Status Change

Definition for base term 3::222 MDC_EVT_COMPONENT_POSN_PROB is: 1. Supply or disposable positioning problem 2. Supply or disposable positioning problem.

Definition for base term 3::418 MDC_EVT_COMPUT_UNDERFLOW is: Underflow was detected in a measurement or calculation.

Definition for base term 3::142 MDC_EVT_CONFIG_ERR is: 1. Device configuration: combination is not valid. 2. {SpO2} Connection not supported

Definition for base term 3::12 MDC_EVT_CONN is: Connection

Definition for base term 3::224 MDC_EVT_CONNECTOR_SHORT is: 1. Connection short 2. Connector short.